hydroelectric turbine cleaning with dry ice blasting
Industries

Dry Ice Blasting Equipment for Power Generation

Cold Jet dry ice blasting delivers exceptional cleaning results for utilities, independent power producers, and power plant operators across all power generation sectors. By replacing water-based, abrasive, and manual cleaning with a dry, non-conductive process, operators clean turbines, generators, and electrical equipment in place, cutting outage time, restoring insulation resistance, and eliminating secondary waste.

Up to 90%

Less Cleaning Time

Non-Conductive

Safe for Electricals

600%

Avg. Insulation Resistance Gain

Contact Us
Overview

Summary

Cold Jet dry ice blasting cleans power generation turbines, generators, and electrical equipment in-place without water, chemicals, or secondary waste. The non-abrasive, non-conductive process safely cleans energized windings across natural gas, hydroelectric, nuclear, steam, and substation operations, cutting cleaning time up to 90% while reducing outages.

Quick Answer

What is dry ice blasting used for in power generation?

Dry ice blasting is a non-abrasive, non-conductive cleaning method used across power generation—natural gas, hydroelectric, nuclear, steam, and substations—to clean gas and steam turbines, HRSGs, heat exchangers, boilers, generators, transformers, switchgear, and electrical windings. Solid CO₂ sublimates to gas on impact, removing carbon dust, oil, salt, coatings, and corrosion without water, chemicals, abrasion, or secondary waste. Because it is non-conductive and dry, it safely cleans energized components with no flash rusting, restoring dielectric integrity—utilities document insulation resistance gains averaging 600%. Equipment is cleaned in-place with little to no disassembly or cooldown, and operators report cleaning-time reductions of up to 90%, minimizing outages. It supports non-destructive testing and produces zero secondary waste, a critical advantage in nuclear facilities. Cold Jet has more than 24,000 machines installed globally.

Cleaning an industrial turbine with dry ice blasting
Exploring dry ice blasting for your operations?Get expert guidance
Challenge

Reduce Outages, Protect Critical Equipment

Fouled generators, turbines, heat exchangers, and electrical windings lose efficiency and raise the risk of unplanned outages and catastrophic failure. Traditional cleaning methods such as chemical solvents, high-pressure washing, and abrasive blasting force cooldown and disassembly, while introducing moisture-induced corrosion, grit entrapment in precision components, insulation degradation, and costly secondary waste.

Cold Jet dry ice blasting is non-abrasive, non-conductive, and completely dry. It removes grease, oil, corrosion, and salts from turbines, windings, and heat exchangers in-place, with little to no disassembly or cooldown. Dry ice sublimates on contact, leaving no moisture, flash rusting, or secondary waste – restoring efficiency while reducing outages.

Zero

Water or Secondary Waste

Increase

Asset Efficiency

Fewer

Unplanned Outages

Non-Abrasive

Protect Critical Assets

Benefits

Benefits of Dry Ice Blasting for Power Generation

Optimize Asset Performance and Minimize Scheduled Outages

Dry ice blasting provides a non-conductive, non-abrasive, zero-waste cleaning solution that removes heavy fouling, carbon buildup, grease, surface oxidation, and corrosive salts without damaging sensitive assets. By eliminating secondary waste and drying time, it allows for immediate inspection and a faster return to service.

Reduce DowntimeReduce Downtime

Dramatic Reduction in Outage Time

Dry ice blasting removes carbon buildup, fouling, and surface oxidation from critical assets—including gas turbines, generators, HRSG tube bundles, and electrical systems. Operators report cleaning time reductions of up to 90% compared to traditional methods. In one instance, a power producer completed the cleaning of an 8-megawatt turbine in just four hours, a task that previously required five days of manual labor. This massive reduction in downtime helps utilities meet aggressive outage schedules and maximize plant availability.

Increase Productivity & EfficiencyEfficiency

Restores Thermal Efficiency and Equipment Performance

Dry ice blasting optimizes heat transfer by removing insulating deposits from finned surfaces and internal cooling passages. Power producers have documented a 12% improvement in power output following dry ice cleaning, compared to just 4% with traditional methods. By penetrating deep into dense tube banks to eliminate bridging, the process reduces differential pressure and lowers fuel consumption, directly improving the plant’s overall heat rate and bottom line.

Non ConductiveNon-Conductive

Safe Around Electrical Equipment

Dry ice cleaning is non-conductive, making it safe for cleaning substations, generator windings, motor stators, transformers, and control systems without risk of electrical shorts or equipment damage. Utilities document insulation resistance improvements averaging 600% with some generators showing 1,000% increases. The moisture-free process prevents electrical tracking in windings and eliminates leakage currents that lead to flashovers and unplanned outages.

Non AbrasiveNon-Abrasive

Protects Equipment from Damage

Cold Jet dry ice blasting is non-abrasive and eliminates the risk of surface erosion or pitting on precision-machined components. Unlike grit blasting, which can alter critical tolerances, or pressure washing, which risks moisture-induced corrosion, dry ice removes stubborn contaminants while preserving the original substrate. This allows for the safe cleaning of delicate winding insulation and turbine blade profiles without the removal of base material.

Secondary WasteNo Waste

Eliminates Secondary Waste

Dry ice sublimates completely upon impact, leaving zero secondary waste. This eliminates the cost and complexity of reclaiming contaminated water, disposing of spent abrasive media, or managing hazardous chemical runoff. While this is a critical advantage for nuclear facilities looking to minimize radioactive waste volumes, it also provides massive logistical savings for fossil and hydro plants.

Applications

Dry Ice Blasting Applications for Power Generation

Cold Jet dry ice blasting equipment provides cleaning and maintenance solutions across five primary power generation sectors: natural gas power plants, hydroelectric facilities, nuclear power generation, steam generation and coal-fired plants, and electrical substations.

Validated For
  • Natural Gas Power Plants
  • Hydroelectric Facilities
  • Nuclear Power Generation
  • Steam Generation & Coal-Fired Plants
  • Electrical Substations

Natural Gas Power Plants

Dry ice blasting maximizes plant availability by restoring critical components to peak thermal efficiency without the wear caused by traditional abrasives. By eliminating secondary waste, facilities can streamline maintenance schedules and return units to operation faster.

Gas Turbine Systems

Dry ice blasting removes carbon deposits, oils, and particulate matter from blades, combustion chambers, and compressor sections. The process cleans turbines in-place without full disassembly. Power producers have reported reducing turbine cleaning time by 90%—an 8-megawatt turbine was cleaned in four hours with dry ice cleaning versus five days when using manual methods.

Heat Recovery Steam Generators (HRSG)

Cold Jet dry ice blasting removes ammonia salts (Ammonium Bisulfate), sulfur deposits, insulation, iron oxide, and fouling from tube bundles without damaging tube bundle welds. Dry ice cleaning reaches between closely-spaced tube fins and restores heat transfer efficiency. Facilities report 40% faster cleaning compared to competitive methods, with power output improvements of 12% versus 4% with traditional methods.

Compressors & Auxiliary Systems

Dry ice blasting cleans rotating equipment, starting motors, alternators, and auxiliary systems without disassembly. The process removes oils, carbon, and debris that accumulate on these components, maintaining equipment reliability while minimizing downtime.

Dry ice blasting removing surface rust from turbine compressor component
Dry ice blasting removing surface rust from turbine compressor component
Dry ice blasting cleans the following equipment in natural gas power plants:
  • Turbine Blades & Combustion Chambers
  • Compressor Sections & Outer Casings
  • Starting Motors
  • Stator & Rotor Windings
  • Alternators & Switchgear
  • Tube Bundles & Sheets
  • HRSG Finned Tubes & Economizers
  • Regenerators & Inlet Houses

Hydroelectric Facilities

Dry ice blasting restores aging assets by removing decades of buildup without damage. The moisture-free process prevents electrical tracking in windings, significantly improves insulation resistance and PI readings, eliminates secondary waste entering the watershed, and extends the operational life of critical components.

Generator Stators and Windings

Cold Jet dry ice blasting safely cleans all generator components—from delicate windings to stubborn contamination on cast iron housings. Utilities document insulation resistance improvements averaging 600%, with some generators showing 1,000% improvements. Polarization indices improved from critical levels (1.04) to acceptable range (2.30). A hydroelectric plant restored a generator considered ‘beyond salvage’ and returned it to full service in just six days using dry ice blasting.

Turbine Components

Dry ice blasting removes sediment and algae from water turbines, penstocks, and draft tubes without damaging turbine runners or requiring complete disassembly. This restores hydraulic efficiency and extends equipment operational life.

Electrical Cabinets & Control Systems

The non-conductive cleaning process safely removes dust and contamination from sensitive control systems, protective relays, and electrical panels. This prevents grounding faults and equipment malfunctions that can lead to system failures.

Cleaning hydroelectric generator with dry ice blasting
Cleaning hydroelectric generator with dry ice blasting
Dry ice blasting cleans the following equipment in hydroelectric facilities:
  • Turbine Runners (Francis, Kaplan, Pelton)
  • Penstocks
  • Draft Tubes
  • Generator Housings
  • Stator & Rotor Windings
  • Excitation Systems
  • Control Cabinets & Protective Relays
  • Switchgear & Electrical Panels

Nuclear Power Generation

Dry ice sublimates completely upon impact, producing zero secondary waste—a critical advantage in nuclear environments where disposing of contaminated water or abrasive media often costs more than the cleaning itself.

Operating Facility Maintenance

Dry ice blasting maintains heat exchangers, steam generators, turbines, pumps, electrical components, and ventilation systems without generating contaminated water or spent media requiring disposal as radioactive waste. The process effectively removes radioactive contamination ranging from Class A through Class C, removes buildup and surface contamination without damaging sensitive components, and reduces radiation exposure time for maintenance personnel.

Decommissioning & Decontamination

Cold Jet dry ice blasting removes radioactive contamination from walls, floors, hot cells, gloveboxes, equipment, and ductwork. The process minimizes waste volume by 90% or more compared to abrasive blasting, significantly reducing disposal costs. During Post-Operational Clean Out (POCO) phases, dry ice blasting removes loose radioactive contamination, dust, scale, and chemical residues from internal plant surfaces, reducing background contamination levels for clearance and verification. Dry ice cleaning decontaminates concrete, steel, and painted surfaces with minimal substrate damage while meeting regulatory standards.

Component & Equipment Cleaning

Dry ice blasting cleans pumps, valves, piping, instrumentation, tools, handling equipment, and robotic systems before reuse, storage, or disposal without damaging sensitive equipment. The process also cleans shielding materials including lead bricks and concrete blocks for safe reuse, and prepares areas for radiological scanning by reducing surface contamination that could affect survey readings.

Nuclear power plant and cooling towers
Nuclear power plant and cooling towers
Dry ice blasting cleans the following equipment in nuclear power facilities:
  • Steam Generators
  • Heat Exchangers
  • Pumps, Valves, & Piping
  • Stator Tubes
  • Hot Cells & Gloveboxes
  • Scaffolding
  • Tooling
  • Ventilation Ducting
  • Floors & Walls
  • Instrumentation & Sensors

Steam Generation & Coal-Fired Plants

Dry ice blasting restores thermal efficiency in coal-fired facilities by removing heavy slag, soot, and scale without secondary waste. It eliminates the risk of corrosion in boiler tubes and allows for immediate inspection or return to service. By maintaining peak heat transfer rates and reducing differential pressure across catalysts, facilities can significantly lower fuel consumption and emissions.

Boiler Systems

Dry ice blasting removes ash, soot, and scale from boilers, superheaters, economizers, and tube banks. It effectively breaks up bridging between tubes that traditional methods struggle to reach. The process leaves surfaces ready for inspection and non-destructive testing, allowing immediate return to service without drying time.

Steam Turbines & Condensers

Cold Jet dry ice blasting handles routine maintenance of steam turbine rotors, diaphragms, and casing internals. It removes deposits from condenser tube sheets and auxiliary cooling systems, improving vacuum performance and overall plant heat rate.

Air Quality Control Equipment

Dry ice blasting is the preferred method for cleaning SCR systems and electrostatic precipitators. It safely clears honeycomb catalysts of fly ash and popcorn ash without the risk of plugging or chemical damage.

Cleaning metallic fins on steam turbine rotor with dry ice blasting
Cleaning metallic fins on steam turbine rotor with dry ice blasting
Dry ice blasting cleans the following equipment in steam generation and coal-fired plants:
  • Boiler Tubes
  • Superheaters
  • Economizers
  • Finned Tube Banks
  • Steam Turbine Blades, Diaphragms, and Casings
  • Air Preheaters
  • Condensers
  • Heat Exchangers
  • Soot Blowers & Wall Blowers
  • Selective Catalytic Reduction (SCR) Systems
  • Electrostatic Precipitators
  • Emission Control Equipment

Electrical Substations

Dry ice blasting restores the integrity of substation components by removing conductive contaminants. The moisture-free process allows utilities to perform critical cleaning during shorter maintenance windows. By eliminating surface pollutants, facilities can prevent leakage currents and flashovers that lead to unplanned outages.

High-Voltage Equipment

Dry ice blasting removes conductive deposits—including salt spray, coal dust, and industrial pollutants—from ceramic and polymer insulators, transformers, circuit breakers, and bushings. By stripping away these contaminants without using water or abrasives, the process restores electrical clearances to safe operating levels and effectively prevents the leakage currents that lead to flashovers, fires, and catastrophic equipment failures.

Control & Protection Systems

Cold Jet dry ice cleaning safely removes dust and contamination that creates grounding faults and equipment malfunctions from control cabinets, protective relays, SCADA equipment, and metering systems.

Distribution Equipment

Dry ice blasting safely cleans capacitor banks, voltage regulators, auxiliary equipment, and distribution infrastructure without extended outages. The process removes environmental contaminants from cooling fins and insulators, ensuring these systems maintain optimal power factor correction and grid stability.

Dry ice blasting is used at electrical substations to clean high voltage insulators
Dry ice blasting is used at electrical substations to clean high voltage insulators
Dry ice blasting cleans the following equipment in electrical substations:
  • Ceramic & Polymer Insulators
  • Transformer Bushings
  • Radiators
  • Circuit Breakers & Isolators
  • Switchgear & Busbars
  • Control Cabinets & Wiring Harnesses
  • Protective Relays
  • SCADA Racks
  • Voltage Regulators
  • Capacitor Banks
What You Need

What Do Power Generation Operators Need for Dry Ice Cleaning?

An effective dry ice cleaning setup for power generation operations requires these essential components.

Dry Ice Blaster

Step 01

Dry Ice Blaster

A dependable and versatile dry ice blaster is essential for power generation maintenance. Cold Jet machines feature our patented Particle Control System (PCS®) for precise control over particle size and cleaning intensity—from gentle MicroParticle settings for electrical insulation to aggressive 3mm pellets for heavy contaminant removal. Portable designs allow operators to bring equipment directly to the areas that need maintenance.

  • 01. Dry Ice Blaster — A dependable and versatile dry ice blaster is essential for power generation maintenance. Cold Jet machines feature our patented Particle Control System (PCS®) for precise control over particle size and cleaning intensity—from gentle MicroParticle settings for electrical insulation to aggressive 3mm pellets for heavy contaminant removal. Portable designs allow operators to bring equipment directly to the areas that need maintenance.
  • 02. Compressed Air — Plant air systems provide adequate compressed air supply. Portable diesel compressors serve as alternatives for remote locations or areas without permanent air infrastructure.
  • 03. Dry Ice Supply — Consistent access to dry ice keeps your maintenance program running smoothly. Cold Jet can connect you with regional dry ice suppliers and help determine order volumes based on your cleaning needs. Coordinate delivery schedules with your maintenance calendar and planned outages.
  • 04. Operator Training — Effective operation of dry ice equipment in power generation requires adequate training. Cold Jet provides comprehensive training that covers machine operation, safety protocols, and best practices for cleaning.
  • 05. Personal Protective Equipment (PPE) — Operators must wear appropriate safety gear including gloves, hearing protection, and eye protection.
Comparison

How Dry Ice Blasting
Compares to Alternatives

See how dry ice blasting stacks up against traditional cleaning methods across the criteria that matter most in power generation.

Criteria
Dry Ice Blasting
Best
Chemical Cleaning
Manual Cleaning
Sand Blasting
Laser Cleaning
Secondary Waste
None – sublimates to gas, no residue
High – spent solvents and wastewater
Moderate – used solvents, rags, debris
High – spent abrasive media and dust
Low – vaporized residue needs extraction
Speed
Fast – up to 90% less cleaning time
Slow – soak and rinse cycles
Slow – labor intensive
Slow – masking and cleanup add time
Slow – point-by-point on large assets
Equipment Damage
None – safe for windings and precision parts
Possible – corrosive to some surfaces
High – scrubbing wears components
High – abrasive, damages surfaces
Possible – heat can alter surfaces
Regulatory Compliance
Strong – non-conductive, no chemicals
Limited – solvent and disposal rules
Inconsistent – operator dependent
Limited – silica/dust exposure rules
Limited – VOC exposure
Downtime
Minimal – clean online, no disassembly
High – disassembly and soak time
High – cooldown and teardown
High – containment and cleanup
Moderate – setup per surface
Environmental Impact
Low – no water/chemicals, reclaimed CO₂
High – hazardous chemical disposal
Moderate – water and chemical use
High – dust and spent media disposal
Moderate – generates VOC & energy intensive
Comparing dry ice cleaning to your current method?Talk to an application expert
Compare Machines

How Do These Dry Ice Blasters Compare for Power Generation?

Side-by-side specs for the Cold Jet blasters suited to power plants, so you can match each machine to generators, turbines, transformers, and boiler equipment during planned outages.

Specification
Aero2® PCS® ULTRA
Aero® 40FP
IceTech Elite 20
Particle Control
Variable(0.3mm to 3.0mm, 28 sizes)
Standard(3mm)
Standard(3mm)
Controls
Digital(7" LCD, Recipes, IoT)
Analog / Standard
Analog / Standard
Feeder Technology
Two-Stage + Defrost Cycle
Advanced Radial Feeder
Horizontal Disk Dosing
Application Intensity
Versatile(Precision to Aggressive)
Moderate to Aggressive
Moderate
Automation & Integration Capable
Yes
No
No
Hopper Capacity
60 lbs(27 kg)
40 lbs(18 kg)
44 lbs(20 kg)
Not sure which blaster fits your job?Get a recommendation
Why Cold Jet

Why Choose Cold Jet Dry Ice Cleaning Machines
in Power Generation

Cold Jet delivers the industry’s most comprehensive portfolio of power generation dry ice cleaning equipment engineered for reliability during critical outage windows. Our machines provide superior ROI and longer-term value.

cold jet dry ice blasters

Proven Industry Experience

We’ve worked with utilities, IPPs, and power plant operators worldwide to address their most demanding maintenance challenges. Cold Jet brings decades of specialized experience serving the power generation industry.

Built for Demanding Environments

Cold Jet dry ice blasting machines are built to withstand rigorous power plant conditions. Our equipment delivers exceptional reliability and substantially longer service life than competing models.

Superior Efficiency

Cold Jet equipment is engineered for maximum efficiency, consuming less dry ice and compressed air than competing systems. This efficient operation directly reduces operating expenses while maintaining superior cleaning performance.

Comprehensive Customer Support

Our service team is here when you need us. We provide operator training, technical support, and equipment repair to keep your operations running smoothly.

Application-Engineered Accessories

Extensive catalog of specialized applicators, blast hoses, and application-specific nozzles optimized for power generation operations.

Ready to make the switch?Talk to us
Trusted by

Proven Performance Across the Power Sector

Cold Jet provides mission-critical dry ice cleaning solutions for the world's most demanding power generation environments.

  • Logo New York Power Authority logo
  • PG&E logo
  • Siemens Energy logo
  • Southern California Edison logo
  • Andritz Hydro logo
  • Baker Hughes logo
  • Eaton Corporation logo
  • EnBW logo
  • First Solar Logo
  • GE Vernova logo
Compliance

Supporting Reliability, Safety & Sustainability

Dry ice blasting helps power generation facilities meet electrical-safety, reliability, and environmental goals without water, chemicals, or secondary waste.

Non-Conductive

Electrical Safety

Cleaning energized windings, transformers, and switchgear requires a method that will not introduce moisture or conductive residue that causes shorts, flashovers, or insulation damage.

How We Comply

Dry ice is non-conductive and completely dry, safely cleaning energized equipment while restoring dielectric integrity—improving insulation resistance, polarization index, and thermal dissipation.

Zero Waste

Waste Minimization & Compliance

Water- and abrasive-based cleaning generate wastewater and spent media, and in nuclear facilities the disposal of contaminated water or abrasive media often exceeds the cost of cleaning itself.

How We Comply

Dry ice sublimates on impact, producing zero secondary waste and reducing radioactive waste volume during POCO and decommissioning – supporting compliance with stringent waste-minimization standards.

No Flash Rusting

Asset Reliability

Unplanned outages and catastrophic failure carry major cost and grid-reliability consequences, and moisture-based cleaning can leave flash rusting on critical components.

How We Comply

Dry, in-place cleaning leaves no moisture or flash rusting and enables more frequent maintenance, reducing unplanned outages and protecting precision components.

Need to meet a specific standard?Talk to an application specialist
FAQ

Frequently Asked Questions

Contact

Ready to Get Started?

Contact us today to discover how our dry ice cleaning machines can enhance your process.