
Summary
Cold Jet dry ice blasting cleans plastic and rubber molds hot and in-press—without cooldown, disassembly, chemicals, or secondary waste. The non-abrasive process removes resin, off-gasses, and release agents from cavities, vents, and complex geometries without wearing critical tolerances—cutting cleaning time up to 75%, reducing scrap, and extending mold life.
What is dry ice blasting used for in plastic and rubber mold cleaning?
Dry ice blasting is a non-abrasive, chemical-free method for cleaning plastic and rubber molds in-place, at operating temperature. Solid CO₂ sublimates to gas on impact, removing resin, off-gasses, cured material, and mold release agents from cavities, vents, parting lines, and hard-to-reach geometries—preventing mold fouling, clogged vents, short shots, splay, burns, and flash. It cleans injection, compression, blow, PET preform, technical, and LSR/LIM molds across Class A–D surfaces without wearing finishes or critical tolerances, so parts stay consistent and scrap drops. Because molds can be cleaned hot and in the press without cooldown, disassembly, or thermal stress, molders reduce cleaning time up to 75%, improve OEE, and extend mold life. Dry ice sublimates on contact, leaving no moisture, chemical, or media residue to cause cross-contamination or scrapped parts. Cold Jet has more than 24,000 machines installed globally.

Traditional Mold Cleaning Damages Tooling and Drains Production Time
Mold fouling from resin, off-gasses, and release agent in cavities and vents causes short shots, splay, burns, and scrap. Cleaning is often delayed because traditional methods cause downtime and damage tooling: scraping and glass bead blasting degrade surface finishes and wear tolerances, chemicals endanger workers, and laser cleaning can strip protective coatings and fails on highly polished surfaces. Most also require pulling the mold from production for cooldown, disassembly, and reassembly, adding significant labor costs.
Cold Jet dry ice blasting is non-abrasive and chemical-free. It cleans molds hot and in the press—no cooldown, disassembly, or thermal stress—removing buildup from cavities and vents without wearing tolerances. With no secondary waste, molders cut cleaning time up to 75%, reduce scrap, and extend mold life.
Class A–D
Mirror Finish to Textured
Fewer
Defects or Rejects
Extended
Production Runs
Zero
Secondary Waste
What are the Benefits of Dry Ice Blasting for Plastic Mold Cleaning and Rubber Mold Cleaning?
Dry ice blasting cleans molds while still hot and online, enabling increased production cycles, improved part quality, and reduced scrap rates.
Dry ice cleaning is non-abrasive and effectively removes contaminants without damaging delicate mold surfaces. Molds can be cleaned at operating temperature and in-situ. This eliminates the need for cool down and disassembly, which allows molds to be cleaned in a fraction of the time – drastically reducing production downtime.
By contrast, traditional methods rely on tedious manual processes with chemicals and hand tools that degrade surface finishes, compromise mold integrity, and shorten mold lifespan. Laser cleaning risks stripping protective coatings and struggles on highly polished surfaces.
Clean molds faster and more effectively
The mold cleaning equipment removes resin off-gasses, cured material, and mold release agents from all areas of the mold, including cavities, crevices, vents, and hard to reach areas. Dry ice blasting cleaning reduces mold cleaning times by up to 75% and helps plastic molders meet stringent productivity demands. It helps molders clean faster, better, and more economically, increasing production capacity and improving product quality.
Clean molds hot and online
Dry ice blasting equipment cleans industrial molds at operating temperature while they are still online without causing thermal stress. Cleaning in-situ eliminates downtime associated with the cooldown, disassembly, and reassembly processes. Injection mold cleaning can be done while the mold is still in-press with dry ice cleaning. Molds can be cleaned more frequently, which significantly increases production cycles and decreases rejection rates. Dry ice blasting equipment for plastic molds is also a more efficient process if cleaning must be done offline.
Protects surface finishes and mold integrity
Dry ice cleaning is non-abrasive and will not cause mold wear or affect mold finishes or critical mold tolerances. This ensures consistent and repeatable results, higher quality parts, and less scrap. The plastic mold cleaning equipment is safe and effective on Class A through D surfaces. Dry ice cleaning significantly reduces high tooling replacement costs and prolongs the lifespan of valuable molds.
Clean complex geometries
Dry ice blasting excels at cleaning the intricate details and tight spaces found in plastic and rubber molds. Dry ice easily cleans complex mold geometries and hard-to-access areas that other methods often miss.
No residue or secondary waste
Dry ice blasting cleaning offers a distinct advantage because it produces no secondary waste. As dry ice sublimates into a gas upon impact, there’s no need for water, harsh chemicals, or other cleaning solutions. This means no moisture, chemicals, or secondary media residue are left on the mold or finished part, preventing cross-contamination and scrapped parts.
Consistently higher-quality parts
Dry ice cleaning helps plastics and rubber manufacturers achieve superior part quality and meet contract specifications. Because the process cleans industrial molds in-place and in a fraction of the time, they can be cleaned more frequently. This leads to consistently high-quality parts, significantly reducing scrap rates and rejected products.
Dry Ice Blasting Applications for Plastic & Rubber Molds
Cold Jet dry ice blasting cleans injection, compression, blow, PET preform, technical, and LSR/LIM molds across the plastics, rubber, medical, aerospace, automotive, and packaging industries.
- Plastics & Composites
- Medical Equipment
- Rubber & Tires
- Aerospace & Aviation
- Automotive Manufacturing
- Packaging
What Types of Molds Can Dry Ice Blasting Clean?
Dry ice cleaning is safe and effective for Class A-D surface molds. The industrial mold cleaning process is being used to clean all types of plastic and rubber molding equipment.
- Injection Molds
- Compression Molds
- Rotational Molding
- Thermoform Molds
- Complex Geometry Molds
- Dip Molding
- Blow Molding
- Extrusion Dies
- Textured Molds
- Technical Molds
- PET Preform Molds
- LSR and LIM Molds
- Aluminum Molds
- Urethane Molds
Dry Ice Blasting is Effective on All Types of Plastic and Rubber Molds
Dry ice blasting machines help plastics and rubber manufacturers reduce scrap and downtime, improve product quality, prolong the life of their equipment, and increase profitability.
Injection Mold Cleaning
Traditional plastic injection mold cleaning and injection mold maintenance products require significant downtime and can be abrasive to the mold. Dry ice blasting for plastic injection mold cleaning cleans molds while still hot and in the press, immediately after a cycle, eliminating the need to wait for molds to cool and be disassembled. By cleaning plastic injection molds consistently, they remain clean and calibrated, which leads molders to experience increased production and efficiency. Dry ice cleaning machines are an ideal injection mold cleaner.
Rubber Mold Cleaning
A major problem faced by rubber molders is mold fouling. Buildup of cured material and sacrificial mold release agents causes sticking molds, blemishes, and unwanted flash on final parts, making them unusable and requiring line shutdowns for cleaning. Traditional cleaning methods such as manual scraping, glass bead blasting, or ultrasonic cleaning can be time consuming, ineffective, damaging to molds, and result in high labor and material costs. Dry ice cleaning offers an in-place, online, quick, and effective way to clean at operating temperatures without causing damage to expensive molds.
PET Preform Mold Cleaning
Dry ice cleaning machines help packaging molders meet stringent productivity demands. They help molders clean faster, better, and more economically, increasing production capacity and improving product quality. Dry ice cleaning allows molds, lock rings, cores, and gate inserts to be cleaned without the disassembly of the stripper plate and while the mold is still in the press.
Blow Mold Cleaning
Industrial mold dry ice cleaning allows aluminum molds, even with beryllium inserts, to be cleaned hot and in-place. The non-abrasive method requires no chemicals and produces no secondary waste. Cold Jet’s specially designed nozzles and applicators allow for cleaning in hard-to-reach spaces to ensure a complete clean every time. A quicker clean means more production time, and the thorough clean allows for consistent quality products with less scrap.
Technical Mold Cleaning
Molders are very familiar with the requirements of precision, high-tolerance, and micro-molding parts and the difficulties that come with them. Keeping small orifices and complex geometries of micro-cavity production molds clean is a critical concern when manufacturing high tolerance plastic parts. Dry ice cleaning easily and efficiently cleans technical production molds.
LSR & LIM Mold Cleaning
Because silicones flash very easily, molds for these high-performance thermoset elastomers are manufactured to critical tolerances, often +/- .0002 inches. During cleaning, protecting the critical dimensions on parting lines, sealing surfaces, and mold finish is vital. Industrial mold dry ice cleaning makes it easy to keep the vents open in order to evacuate the air out of the mold prior to injection – this helps to produce high quality molded parts. With dry ice cleaning, you can clean molds in the machine at processing temperature without causing mold wear.




Dry Ice Cleaning for Plastic and Rubber Mold Cleaning is Used in a Variety of Industries
Cold Jet offers dry ice cleaning equipment for plastic molds, rubber mold dry ice cleaning equipment, and injection mold cleaners for a variety of industries.
How Dry Ice Blasting
Compares to Alternatives
See how dry ice blasting stacks up against traditional cleaning methods across the criteria that matter most in plastic and rubber mold cleaning.
| Criteria | Dry Ice Blasting best | Chemical Cleaning | Manual Cleaning | Ultrasonic Cleaning | Laser Cleaning |
|---|---|---|---|---|---|
| Secondary Waste | None – sublimates to gas, no residue | High – spent solvents and residue | Moderate – scrapings, rags, solvent | High – contaminated chemical bath | Low – vaporized residue needs extraction |
| Speed | Fast – up to 75% less cleaning time | Slow – soak, scrub, rinse | Slow – hand scraping is labor intensive | Slow – remove molds, batch soak | Slow – point-by-point on surfaces |
| Equipment Damage | None – non-abrasive, preserves tolerances | Possible – residue and corrosion | High – scraping wears finishes | Low – but size-limited by tank | Possible – can strip mold coatings |
| Regulatory Compliance | Strong – no chemicals, no waste | Limited – solvent handling and disposal | Inconsistent – operator dependent | Moderate – chemical bath disposal | Limited – VOC exposure |
| Downtime | Minimal – clean hot, in-press | High – cool down and soak time | High – teardown and scrubbing | High – molds offline to soak | Moderate – slow per-surface setup |
| Environmental Impact | Low – recycled CO₂, no chemicals | High – hazardous chemical disposal | Moderate – solvent and rag waste | Moderate – chemical bath disposal | Moderate – generates VOC & energy intensive |
What Do Molders Need for Dry Ice Cleaning?
An industrial mold dry ice cleaning configuration at your site relies on several key parts:

Step 01
Dry Ice Blaster
A successful industrial mold cleaning process starts with an easy to use and mobile dry ice cleaning machine. Cold Jet offers a complete range of dry ice blast cleaning machines, featuring advanced models with IoT connectivity and our patented Particle Control System (PCS®). This innovative technology gives you the power to precisely adjust cleaning parameters and dry ice particle size, allowing for very delicate to more aggressive cleaning. Each blaster arrives ready with blast and air hoses, an applicator, and a nozzle for your specific application.
- 01. Dry Ice Blaster — A successful industrial mold cleaning process starts with an easy to use and mobile dry ice cleaning machine. Cold Jet offers a complete range of dry ice blast cleaning machines, featuring advanced models with IoT connectivity and our patented Particle Control System (PCS®). This innovative technology gives you the power to precisely adjust cleaning parameters and dry ice particle size, allowing for very delicate to more aggressive cleaning. Each blaster arrives ready with blast and air hoses, an applicator, and a nozzle for your specific application.
- 02. Compressed Air — Most molding facilities have existing filtered air systems that can supply the required compressed air. Cold Jet dry ice blasters typically need 100 cfm (2.8 m³/min) at 80 psi (5.5 bar) to operate effectively.
- 03. Dry Ice Supply — A reliable supply of dry ice is needed to ensure you have dry ice when you need it. Average consumption is approximately 88 lbs. per hour. We can help you identify a dry ice supplier and recommend the amount you should order based on your needs. Once identified, establish a delivery schedule that aligns with your maintenance and production schedules.
- 04. Machine and Operator Training — To ensure your team can effectively and safely use your dry ice cleaning equipment for plastic molds, proper training is essential. Cold Jet provides a comprehensive training course that equips operators with the necessary techniques and safety guidelines for optimal cleaning practices.
- 05. Personal Protective Equipment (PPE) — Always ensure your cleaning team wears the correct safety gear, including gloves, hearing protection, and eye protection when operating your plastic mold cleaner or injection mold cleaner.
What Is the Best Dry Ice Blaster
for Plastic Molds and Rubber Molds?
Cold Jet provides a full range of dry ice blasters specifically for plastic mold cleaning and rubber mold cleaning. Our systems are user-friendly, built to last, and are easily portable, making them perfect for any molding operation.

Aero2® PCS® ULTRA
The Aero2 PCS ULTRA is a highly versatile machine for all types of plastic molds and rubber molds. The mobile dry ice blaster handles everything from gentle cleaning with MicroParticle dry ice to aggressive cleaning of larger molds using 3mm dry ice. The machine is an ideal industrial mold cleaner and injection mold cleaner.

i3 MicroClean® 2
The i3 MicroClean 2 features intuitive controls in a lightweight, compact design. Users can easily transport the dry ice blaster right up to the molding machine. You can easily adjust cleaning parameters to lock in the ideal settings for your specific application. The mold cleaning equipment is ideal for plastic mold cleaning, cleaning plastic injection molds, and plastic mold maintenance.

i3 MicroClean®
The i3 MicroClean is an efficient, lightweight, and time-tested dry ice cleaning machine that is ideal for any type of plastic mold cleaning or rubber mold cleaning application, including plastic injection mold cleaning.
How Do These Dry Ice Blasters Compare for Mold Cleaning?
Side-by-side specs for the Cold Jet blasters molders use most, so you can match particle control and intensity to residue, release agents, and vents in plastic and rubber molds.



| Specification | Aero2® PCS® ULTRA | i3 MicroClean® 2 | i3 MicroClean® |
|---|---|---|---|
| Particle Control | Variable(0.3mm to 3.0mm, 28 sizes) | Microparticles(Shaved) | Microparticles(Shaved) |
| Controls | Digital(7" LCD, Recipes, IoT) | Digital(7" LCD, Recipes, IoT) | Analog / Standard |
| Feeder Technology | Two-Stage + Defrost Cycle | Radial Feeder | Radial Feeder |
| Application Intensity | Versatile(Precision to Aggressive) | Delicate / Precision | Delicate / Precision |
| Automation & Integration Capable | Yes | Yes | No |
| Hopper Capacity | 60 lbs(27 kg) | 25 lbs(11 kg) | 20 lbs(9 kg) |
Why Invest in Cold Jet Machines for Rubber or Plastic Mold Cleaning?
Cold Jet offers a wide range of plastic mold dry ice cleaning equipment, rubber mold dry ice cleaning equipment, and injection mold cleaners. When incorporating dry ice blasting into your plastic mold cleaning and rubber mold cleaning processes, you need a durable and reliable machine that you can count on when you need it. Cold Jet machines deliver faster ROI and greater value than competitors.

Mold Cleaning Expertise
With decades of experience in the plastics and rubber sectors, Cold Jet has developed an unparalleled understanding of the critical cleaning challenges and operational demands that plastics molders and rubber molders experience.
Trusted by Plastic and Rubber Molders
With over 24,000 dry ice cleaning machines installed worldwide, including at leading plastics and rubber manufacturers, Cold Jet is the trusted solution for industrial mold dry ice cleaning.
Industry Leading Reliability
Our machines are engineered to thrive in high-production environments. Cold Jet dry ice blasters offer unmatched reliability and a significantly longer lifespan than competitor models.
Lower Operating Costs
Cold Jet dry ice cleaning equipment for plastic molds is designed for maximum efficiency, using significantly less dry ice, compressed air, and electricity than competitor machines. This directly reduces your daily operating costs without compromising on the highest standards of cleaning quality or safety.
Unmatched Support and Training
Our regional technicians are readily available and bring a deep understanding of the unique needs of molders. We offer both expert maintenance services and comprehensive equipment training to ensure your team’s success.
Application Specific Accessories
Cold Jet offers a wide array of accessories, including various applicators, blast hoses, and application-specific nozzles, so you can perfectly configure your setup for your unique operational needs. We will help you find the perfect nozzle for your specific mold.
Plastic molders and Rubber molders around the world rely on Cold Jet
With a global install base of 24,000+ that consists of companies large and small – Cold Jet delivers valuable dry ice cleaning equipment for plastic molds and rubber molds.
Supporting Quality, Safety & Sustainability
Dry ice blasting helps plastic and rubber molders meet part-quality, worker-safety, and environmental goals without abrasives or chemicals.
Contract Specification Compliance
Abrasive cleaning wears mold finishes and critical tolerances, causing blemishes, flash, and scrap that jeopardize contract specifications.
The non-abrasive process is safe on Class A–D surfaces and preserves finishes and tolerances, delivering consistent, repeatable parts that meet contract specifications with less scrap.
Hot Mold Handling Safety
Pulling hot molds for cleaning and using chemical cleaners and hand tools expose operators to burns, chemical hazards, and strain.
In-place, in-press cleaning eliminates hot-mold handling and chemical cleaners, addressing burn, chemical-exposure, and repetitive-strain hazards.
Spent Media and Chemical Waste
Sandblasting and chemical rust removers generate spent media, chemical waste, and wastewater that require cleanup and disposal.
Dry ice sublimates on contact, producing zero secondary waste—no spent media, chemical waste, or wastewater—eliminating disposal costs and environmental concerns.
PackagingPackaging Molder Cuts Mold Cleaning Time to Under 45 Minutes
Case Study
Read more
Automotive ManufacturingInjection Mold Cleaning Cut From 12 Hours to 1 With Dry Ice Blasting
Case Study
Read more
Plastics & CompositesRubber Mold Cleaning Time Cut From 6 Hours to 30 Minutes
Case Study
Read more
Plastics & CompositesPrecision Plastic Molder Cuts Mold Cleaning From 4 Hours to 15 Minutes
Case Study
Read more
Dry Ice BlastingPlastic Molder Cuts 3 Days of Downtime with Dry Ice Blasting
Blog
Read more










