Case StudyGeneral Manufacturing
Bonazza Dry Ice Blasting

Bonazza Dry Ice Blasting

Homeowner Restores 15-Year-Old Cedar Log Home Without Wood Damage

4 min read

TL;DR

A 15-year-old cedar log home in Bonfield, Ontario had built up layers of failing stain, dirt, and mold that needed removal before restaining, without water damage or abrasive blasting media. Bonazza Dry Ice Blasting used Cold Jet's Aero 40 to strip 1,600 square feet of exterior surface cleanly, saving 3-4 days versus sand or corn cob blasting.

The Challenge

Fifteen Years of Stain, Dirt, and Mold Buildup on Delicate Cedar Logs

In order to properly restore a log home, the exterior must be thoroughly cleaned, sanded and then stained. If the surface is not cleaned thoroughly to remove all contaminants, the new layer of stain and sealant will not adhere correctly and will not last long-term. Oftentimes, there are multiple layers of stain that need to be cleaned and removed before a new layer can be added and the log home’s exterior fully restored.

A homeowner in Bonfield, Ontario, wished to restore his 15 year old cedar log home and bring it back to its original beauty. Over the years, the exterior stain had begun to peel and become layered with dirt and mold. The exterior had been re-stained multiple times but never cleaned in between, causing a 15 year buildup of stain, dirt and mold. In order to put on a fresh, new coat of stain, all of the old layers must first be removed. The team at Bonazza Dry Ice Blasting was contacted to do the job.

Traditional methods of surface preparation were considered, including pressure washing, but the water would get into the wood and cause the stain to peel sooner.

Blasting with corn cob, sand, soda, walnuts, and glass would be too abrasive and cause a large mess. Chemical stripping was an alternative but would introduce safety and environmental considerations, as well as add additional time to the project as the wood would need to dry after the chemical treatment. Hand sanding as an option would be extremely time and labor intensive. In order to properly re-stain and restore the home, a less aggressive and more efficient cleaning method was needed.

Cedar log home restoration with dry ice blasting
The Solution

Non-Abrasive Dry Ice Removes Stain Without Adding Moisture to the Wood

Cleaning with Cold Jet’s dry ice cleaning technology was the perfect solution because it uses non-abrasive media in the form of recycled CO2 pellets that will not damage surfaces. The dry ice media is introduced into a pressurized air stream at user-controlled speeds and sublimates – or turns back into a gas – upon impact, lifting away the contaminant safely, without leaving behind any secondary waste or residue.

“

Dry ice cleaning can take years off the look of a log home. It takes a thin layer of wood off all the logs – about 1/16 of an inch – leaving all of the milling marks. This is a great way to rejuvenate the interior and exterior of a log home.

”
— Vinni Bonazza, Owner

Dry ice cleaning is odorless, does not add moisture back to the wood and can be done cleanly, with no hazardous solutions dripping on workers. It can be used on all types of wood, including pine, fir and cedar. Even though cedar shakes are soft and thin, dry ice is soft enough not to penetrate too deeply or damage the wood. Dry ice also works well on cleaning teak, one of the hardest types of wood to clean or strip.

The Results

A Like-New Exterior, Finished Days Ahead of Alternative Methods

1,600

square feet

Cedar log exterior surface area, using approximately 1,500 lbs of dry ice

3-4

days

Compared to sand or corn cob blasting, plus ~2 days for sanding

The team at Bonazza Dry Ice Cleaning used an Aero 40 to clean a total of 1,600 square feet on the exterior of the cabin. The nozzle used allowed them to clean at a steady pace because the dry ice particles were moving at a continuous flow. Altogether, 1,500 pounds of dry ice pellets were used on the project. Once fully cleaned, the surface was lightly sanded and then two fresh coats of stain were applied to complete the restoration process. The entire log home restoration project time included 24 hours of cleaning and surface preparation with dry ice, 52 hours of sanding and 33 hours of staining.

“

The project was on schedule and incredibly fast. We saved at least three to four days when compared to sand or corn blasting and two days of sanding time. The log home looks brand new – it came out 110%.

”
— Vinni Bonazza, Owner

Using a Cold Jet Aero 40, the team cleaned 1,600 square feet of exterior surface with roughly 1,500 pounds of dry ice pellets. After a light sanding, two fresh coats of stain completed the restoration in 24 hours of dry ice cleaning, 52 hours of sanding, and 33 hours of staining — saving an estimated 3-4 days versus sand or corn cob blasting and about 2 days of sanding time.

Contact

Ready to Get Started?

Contact us today to discover how our dry ice cleaning machines can enhance your process.